整機工作原理:
Working principle of the whole machine:
工作前由裝載機(配料機地下安裝時可用人工上料)分別向各個儲料斗供給砂、石物料。
Before the work, the loader is supplied with sand and stone materials to each storage hopper respectively.
按配料控制儀說明書要求,向配料控制儀輸入配方(不用的物料一定設為0)。按下配料按鈕后,配料機便開始進入自動配料程序。其工作過程為:首先料Ⅰ皮帶機開始工作,將料Ⅰ輸送到稱料斗,當稱料斗內料Ⅰ的重量達到其設定值時,料Ⅰ皮帶機自動停止;接著料Ⅱ皮帶機自動開啟,當稱料斗中的物料重量達到料Ⅰ、料Ⅱ的設定值之和時,料Ⅱ皮帶機停止,料Ⅲ皮帶機開始工作… …,如此四種物料配齊后,機器便處于等待狀態。這時按下出料按鈕,出料皮帶機工作,將配好的混凝土干料卸入攪拌機料斗。出料完畢后,出料皮帶機自動停止,并自動開始第二個循環配料,第二個循環配料結束,又等待出料,如此往復。
According to the specification requirements of the batching control instrument, the formula is input to the batching controller (no material must be set to 0). When the batching button is pressed, the batching machine begins to enter the automatic batching program. The working process is as follows: firstly, I feed belt machine began to work, I will be transported to the known material hopper, when I called the hopper in weight reached the set value, the automatic stop of feeding belt machine; then the material automatically open II belt machine as the material in the hopper material material weight reached I, II set the value of the material, II belt machine stops, III belt machine start working material...... So, the four materials are complete, the machine is in a wait state. Then press the discharging button, a material conveyer, concrete material with good discharge into the mixer hopper. After the discharge is completed, the belt conveyor automatically stops, and automatically starts second cycle ingredients, ends with second cycle ingredients, and then waits for discharging, so reciprocating.
公司名稱:濟南笨鳥先飛自流平服務中心
聯系人:騰師傅
聯系電話1:18560146326
聯系電話2:13688634565
固定電話:0531-58969192
地址:濟南市各地均可服務
諾商基于多年的優化經驗和品牌基礎推出的諾商商道系統,諾 |